Skip to main content
EUCONXSupply Chain
Unfinished parking deck with concrete columns: black bitumen membrane strips laid over part of the concrete, upright and lying membrane rolls on and beside them; on the left a gas cylinder with hose and a torch head, parapet and city in the background.

AI-generated illustrative image

Material spotlight

Single-layer parking deck waterproofing: 4.5 mm SBS + TPU membrane

Ahmet Alptekin Kasar

Founder, Managing Director

7 min

Updated: 2026-11-16

This page is for waterproofing contractors, developers, general contractors and construction groups working on parking decks, podium slabs over underground car parks and terrace slabs in Hungary. It focuses on parking decks and on the single-layer approach. Full build-ups for walkable terraces are covered in our article on walkable roof terrace insulation.

What single layer means on a parking deck

Classic bitumen build-ups on concrete decks use more than one layer. Bonus developed Ultrabond to be installed as one. According to the manufacturer's catalogue, the membrane bonds to the concrete over its full surface without voids. With no gap between membrane and deck, water that enters at a damaged spot cannot travel sideways under the sheet. That is the manufacturer's case for single-layer protection.

The manufacturer describes the build of the sheet as elastomeric SBS-modified bitumen, TPU (thermoplastic polyurethane) reinforcement and a high-grammage polyester felt carrier. Bonus credits the TPU with wear resistance and with letting the sheet heat up and cool down quickly during torching. A standard version and a UV-resistant slate-coated version are listed.

The manufacturer's areas of use are basement retaining walls, roofs and terraces, parking areas, and walkable and non-walkable terraces. According to Bonus, Ultrabond received the "Yılın Yatırımı" (Investment of the Year) award at the Yalıtım Sektörü Başarı Ödülleri in 2025.

Schematic single-layer build-up for a parking deck or terrace slab, from bottom to top: concrete deck, light bituminous primer 0.1–0.150 L/m², Bonus Ultrabond 4.5 mm in one layer, torch-applied fully bonded, overlaps 10 cm lengthwise and 15 cm crosswise, protection and wearing course to the designer's specification; manufacturer data: 4.5 mm, polyester felt carrier, −20 °C, roll 1 × 8 m, tensile strength 1000 / 800 N/5 cm
Schematic, not to scale. Source: Bonus Yalıtım membrane catalogue, https://www.bonusyalitim.com.tr/media/urunbrosur/50556f-membran-katalog-en.pdfDownload PNG
Layer or propertyManufacturer value
Concrete deckold or new concrete, free of loose or moving particles
Primerlight bituminous primer, 0.1–0.150 L/m², no thick film
WaterproofingBonus Ultrabond, 4.5 mm, single layer, torch-applied, fully bonded
Overlaps10 cm lengthwise, 15 cm crosswise; joints staggered by 20 cm
Protection and wearing courseto the designer's specification
Carrierpolyester felt
Low-temperature flexibility−20 °C
Roll size1 × 8 m
Tensile strength, MD / CD1000 / 800 N/5 cm

Source: Bonus Yalıtım membrane catalogue (EN), Ultrabond.

Substrate and primer

The manufacturer treats surface preparation as a condition of installation. The concrete must be free of loose or moving particles and primed with a light bituminous primer. The stated rate is 0.1–0.150 L/m², applied without building up a thick film. The primer binds dust and helps the membrane bond. Bonus warns that too much primer forms a thick layer that weakens adhesion.

On refurbishment jobs this matters most. The membrane is listed for old and new concrete, but loose material, remains of old coatings and damaged areas on an existing deck have to be dealt with first. How much work that means is settled at the survey.

Close-up: the edge of a black bitumen membrane lying on primed, darkened concrete, with a glossy bead of molten bitumen squeezed out along the edge; unprimed light grey concrete on the left
AI-generated illustrative image

An even bead of bitumen along the sheet edge is what a contractor looks for when torching: it shows that the underside has melted and bonded across the full width.

Overlaps and joints

Bonus specifies heating the sheet over its whole surface, with overlaps of 10 cm lengthwise and 15 cm crosswise and end joints staggered by 20 cm. In a single-layer system there is no second sheet to cover a poor seam, so the quality of the overlaps is the quality of the system.

Upstands at parapets, drains, movement joints and connections to walls are detailed by the designer. The catalogue gives no dimensions for them, so neither do we.

Single layer or a classic multi-layer build-up

A single layer means less material to lay and less time on the deck; Bonus names both as advantages. Classic multi-layer bitumen build-ups stack thinner sheets. Bonus Premium EP 300 is one such sheet: a 3 mm SBS-modified bitumen membrane, flexible down to −20 °C according to the manufacturer, in 10 × 1 m rolls.

Which system goes on a given deck is the designer's decision, based on loads, the build-up and the project specification. We can supply materials for either. The difference between APP- and SBS-modified sheets is covered in APP vs SBS bitumen membrane.

Terrace slabs

The principle on a terrace is the same: primed concrete, one fully torch-bonded layer, sound overlaps and upstands. The difference is in what goes on top. Finishes, falls and insulation for walkable terraces are covered in walkable roof terrace insulation.

Roof terrace with a concrete parapet: parallel strips of black bitumen membrane on the slab and a membrane strip turned up at the foot of the parapet; on the left unprimed concrete with two membrane rolls, trees, houses and the sea in the background
AI-generated illustrative image

Here the sheet is turned up at the base of the parapet. Upstand height and termination are set by the designer.

Insulated decks and inverted build-ups

Where there is heated space below the slab, or the build-up calls for thermal insulation, extruded polystyrene (XPS) can go above the waterproofing. In this inverted build-up the membrane sits under the insulation, protected. ODE Isıpan XPS is made for terrace and inverted roof build-ups among others; the designer chooses the compressive strength class and thickness. Inverted and warm roofs are compared in flat roof insulation: inverted vs warm roof.

Supply from Turkey

EuConX supplies materials; it does not install. A contractor partner does the installation. Ultrabond ships in rolls; per the manufacturer's data sheet a roll covers 8 m² and a pallet 200 m². We do not publish a price for this membrane; the final price follows a survey.

In the order, state the version (standard or slate-coated), the deck area and the roll count that follows from it, the primer quantity and the delivery schedule. Bonus declares the membrane against TS EN 13707 and TS EN 13969; ask for the declaration of performance (DoP) and CE marking for the exact product ordered.

StepWhat happensTime
Enquiryyou send the deck area, the build-up, the delivery point and the schedule–
Replywe respond to the enquirysame working day
Order to site, when not in stockloading at the manufacturer, transit, deliverytypically 1–2 weeks
Transit Turkey → Hungaryfrom the manufacturer to the Hungarian warehouse or site3–5 days, about 5 on average
Deliveryanywhere in Hungary, to the given siteas scheduled

Source: EuConX company data.

In 2025–26 we delivered 4.3 million m² of membranes, with 98% of deliveries on time. On a large deck it pays to split delivery into phases so that rolls do not sit on site for long.

Request a quote

Send the deck area, the planned build-up, the delivery point and the schedule: contact · +36 30 485 0258 · info@euconx.com. We reply the same working day.

Frequently asked questions

Is one layer of bitumen membrane enough on a parking deck?

Bonus developed Ultrabond for single-layer installation on parking decks and terraces. It bonds over its full surface, so according to the manufacturer water cannot migrate under the sheet. Whether a given deck gets a single-layer or a multi-layer system is the designer's decision.

What substrate can the membrane go on?

Old or new concrete, according to the manufacturer. The surface must be free of loose or moving particles and primed with a light bituminous primer at 0.1–0.150 L/m².

What overlaps are required?

The manufacturer specifies 10 cm lengthwise and 15 cm crosswise, with joints staggered by 20 cm.

How cold can it get before the membrane loses flexibility?

The manufacturer states low-temperature flexibility down to −20 °C.

What goes on top of the waterproofing on a parking deck?

A protection and wearing course to the designer's specification. On insulated decks, XPS can sit above the membrane in an inverted build-up.

Does EuConX install the membrane?

No. We supply materials from Turkey, 3–5 days in transit, with delivery anywhere in Hungary. A contractor partner installs, and the final price follows a survey.

Sources

1. Bonus Yalıtım: Membrane catalogue (EN), Ultrabond (build, areas of use, primer, overlaps, technical data, award)

2. Bonus Yalıtım: Yılın Yatırımı Ödülünün Sahibi Bonus Ultrabond Membran Oldu (award, single-layer application, lateral water migration)

3. Bonus Yalıtım: Ultrabond technical data sheet (roll, pallet) and Premium EP 300 data sheet

4. EuConX: delivery and company data (volumes, on-time rate, transit, lead time, reply time)

parking deck waterproofing membranesingle-layer bitumen membraneSBS membrane 4.5 mmterrace waterproofingcontractors

Planning a project? Let’s talk.

Send the material schedule or project requirements. We’ll help match the product and prepare a clear quotation.