Skip to main content
EUCONXSupply Chain
A timber-frame wall under construction: grey-green stone wool boards fitted tightly between the studs, a metal pipe running diagonally across, a gloved hand trimming a board with a knife.

AI-generated illustrative image

Material spotlight

A1 stone wool in timber-frame houses: fire class and fire resistance

Ahmet Alptekin Kasar

Founder, Managing Director

6 min

Updated: 2026-11-20

This piece is for timber-frame and prefab manufacturers, facade contractors and buyers who have to order non-combustible insulation for a project. We use the data of the Bonus Premium F 120 Stone Wool Board as the example.

Reaction to fire and fire resistance are two different things

Reaction to fire describes how a material behaves when fire reaches it: whether it ignites, how much heat and smoke it gives off. The classes run from A1 to F, with A1 the best. The class is stated in the manufacturer's declaration of performance (DoP) and is part of the CE marking.

Fire resistance is a property of a building element: for how many minutes it keeps its load-bearing capacity (R), integrity (E) and insulation (I). A REI 60 timber-frame wall meets all three for 60 minutes. No single material delivers that; the studs, linings, insulation and fixings do together, proven by a test and a classification report.

Why the insulation still matters

In a timber-frame wall the insulation sits between the studs and protects the timber from the cavity side in a fire. Documents for tested wall build-ups therefore name the insulation type, its thickness and often a minimum density. If the report says stone wool, the bay gets stone wool, even if another A1 material would perform the same thermally.

The ODE glass wool products EuConX supplies are A1 as well. The difference is not in the class but in what the tested system specifies. Our comparison of the two materials covers this too.

On the facade the question is different

On a timber-frame wall, rendered external insulation (ETICS) is a system whose European Technical Assessment (ETA) names the type and properties of the insulation board. For stone wool the key ones are tensile strength perpendicular to faces, density and dimensional stability. The Bonus Premium F 120 Stone Wool Board declares them as follows:

PropertyValue
Reaction to fireA1
Density120 kg/m³ ± 10%
Thermal conductivity λD0.037 (50–80 mm), 0.038 (100 mm) W/(m·K)
Tensile strength perpendicular to facesTR10
Thickness toleranceT5
Short-term water absorptionWS ≤ 1 kg/m²
Water vapour diffusion resistanceMU 1
Dimensional stabilityDS(70,-)

Source: EuConX technical datasheet.

MU 1 is particularly useful on a timber-frame wall: the board is vapour-open and does not trap moisture in the construction. The hygrothermal check of the build-up still has to be done.

What to put in the order

The reaction-to-fire class, density, TR value, thickness and the system or report the board has to match. We send the declaration of performance with the offer, so the designer or system holder can compare before the order. The board comes in 50, 70, 80 and 100 mm at 600 × 1200 mm; 30 mm can be produced on request (λD 0.036), 20 mm cannot.

Frequently asked questions

What does it mean that a stone wool board is A1?

It is in the best reaction-to-fire class under EN 13501-1: non-combustible, with no contribution to fire. The class is stated in the declaration of performance.

Does A1 insulation make a wall fire-resistant?

Not on its own. Fire resistance (REI) belongs to the whole construction and is proven by a test and a classification report.

Can glass wool be A1 too?

Yes. ODE Starflex and Lunaflex rolls and ODE Evomineral partition boards are A1. Which one may go into a wall is decided by the documents of the tested construction.

Which stone wool goes under render on a timber-frame wall?

The one the facade system's ETA allows. Typically a rigid board with a stated density and tensile strength; the Bonus Premium F 120 Stone Wool Board is TR10.

Which thicknesses does the Bonus Premium F 120 Stone Wool Board come in?

50, 70, 80 and 100 mm at 600 × 1200 mm. 30 mm can be produced on request; 20 mm cannot.

Sources

1. EuConX technical datasheet, stone wool board 120: https://euconx.com/en/products/datasheets/stone-wool-board-120

2. Commission Decision 2000/147/EC on the classification of the reaction to fire performance of construction products: https://eur-lex.europa.eu/eli/dec/2000/147/oj

3. Regulation (EU) No 305/2011 (construction products, CE marking, declaration of performance): https://eur-lex.europa.eu/eli/reg/2011/305/oj

4. EN 13501-1 (reaction to fire classification) and EN 13501-2 (fire resistance classification)

A1 stone wooltimber frame fire safetynon-combustible insulationBonus Premium F 120 kg/m³ETICS on timber framemanufacturers

Planning a project? Let’s talk.

Send the material schedule or project requirements. We’ll help match the product and prepare a clear quotation.